|
|
| (3 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| | + | == Link to harness building == |
| | + | https://vansairforce.com/community/showthread.php?t=152279 |
| | + | |
| | == Drawing == | | == Drawing == |
| − | {{#drawio:Panel Wiring GRT}} | + | {{#drawio:Panel Wiring Garmin}} |
| − | | |
| − | == Docs ==
| |
| − | https://static.garmin.com/pumac/GTX327Transponder_InstallationManual.pdf<br>
| |
| − | http://grtavionics.com//media/Remote-EIS-Install-and-User-Manual-A.pdf<br>
| |
| − | http://grtavionics.com//media/GPS-Safe-Fly-Install-Manual-Rev-P.pdf<br>
| |
| − | http://grtavionics.com//media/ARINC-429-External-Module-Single-Board-Rev-A.pdf<br>
| |
| − | http://grtavionics.com//media/10-1-Sport-Horizon-Installation-Manual-Rev-A.pdf<br>
| |
| − | https://uavionix.com/downloads/echo-uat/echoUAT-User-and-Installation-Guide.pdf<br>
| |
| − | https://www.valavionics.com/uploads/2/1/5/0/21502568/nav_2kr_install_manual_original_issue_june_2013.pdf<br>
| |
| − | https://www.bendixking.com/content/dam/bendixking/en/documents/document-lists/downloads-and-manuals/8300-008-DigiFlight-II-Series-Autopilot-Installation-Manual.pdf<br>
| |
| − | | |
| − | == old drawing ==
| |
| − | {{#drawio:Panel Wiring}}
| |
| − | | |
| − | == script ==
| |
| − | | |
| − | This makes the anchor points on the draw.io stuffs
| |
| | | | |
| − | #!/bin/bash
| + | == Notes == |
| − |
| + | Do I need to wire the power or gnd to P4601 on the g3x or just the serial to the GSU 25? |
| − | if [ -z "$1" ] || [ -z "$2" ]; then
| |
| − | echo "usage: $0 <number of elements> <side>"
| |
| − | exit
| |
| − | fi
| |
| − |
| |
| − | if [ "$2" == "left" ]; then
| |
| − | SIDE=0
| |
| − | else
| |
| − | SIDE=1
| |
| − | fi
| |
| − |
| |
| − | echo "points=["
| |
| − |
| |
| − | POINTS=$(($1+1))
| |
| − | POINTS=$1
| |
| − | SPACING=`echo "scale=3; 1/$POINTS" | bc`
| |
| − | NUM=`echo "scale=3; $SPACING/2" | bc`
| |
| − |
| |
| − | for (( I=1; I<=$POINTS; I++ )); do
| |
| − |
| |
| − | if [ "$I" == "$POINTS" ]; then
| |
| − | echo "[${SIDE},0${NUM}]]"
| |
| − | else
| |
| − | echo "[${SIDE},0${NUM}],"
| |
| − | fi
| |
| − |
| |
| − | TMP=`echo "scale=3; $NUM + $SPACING" | bc`
| |
| − | NUM=$TMP
| |
| − |
| |
| − | done
| |
